Solar cell testing under AM0 (Air Mass Zero) spectrum conditions evaluates the electrical performance of photovoltaic devices designed to operate outside the Earth's atmosphere, where incident solar irradiance reaches approximately 1366 W/m². By reproducing the extraterrestrial solar spectrum defined in standards such as ASTM E490 and ISO 15387, this testing delivers the current-voltage characteristics, conversion efficiency, and spectral response data required for satellite and spacecraft power system design. Accredited third-party laboratories, cell manufacturers, and space research institutions rely on AM0 characterization to qualify space-grade solar cells before flight deployment.
Technical Overview
The AM0 (Air Mass Zero) spectrum represents the solar radiation incident at the top of the Earth's atmosphere, unmodified by atmospheric absorption and scattering. Compared with the AM1.5 spectrum used for terrestrial photovoltaic testing, the AM0 distribution contains significantly stronger ultraviolet content and lacks atmospheric absorption bands caused by ozone, water vapor, and carbon dioxide. The integrated irradiance, known as the solar constant, is defined as 1366.1 W/m² in ASTM E490 and 1367 W/m² in ISO 15387, with the spectrally relevant measurement range extending approximately from 200 nm to 2600 nm.
Because space solar cells operate in this extraterrestrial radiation environment, ground-based performance evaluation must faithfully reproduce AM0 conditions. Testing under an incorrect spectrum introduces systematic errors in short-circuit current that can propagate into inaccurate power predictions for on-orbit operation. Professional AM0 testing therefore combines a spectrally matched solar simulator, a traceable reference cell, and rigorous temperature control to yield results that are directly comparable between laboratories worldwide.
- ASTM E490: Standard Solar Constant and Air Mass Zero Solar Spectral Irradiance Tables
- ISO 15387: Space systems, space solar cells, requirements and measurement procedures
- ASTM E927: Classification of solar simulators for photovoltaic testing (methodology reference)
- IEC 60904 series: Measurement of current-voltage characteristics, reference devices, spectral response, and linearity
Testing Samples
Single-Junction Space Solar Cells
High-purity silicon cells engineered for space use, including thin wafer designs with back-surface reflectors and front-surface fields, constitute a classic sample category. Single-junction III-V cells such as gallium arsenide (GaAs) and indium phosphide (InP) devices are also tested individually to establish baseline performance parameters under AM0 illumination.
Multi-Junction III-V Compound Solar Cells
Lattice-matched triple-junction structures such as GaInP/GaInAs/Ge, dual-junction InGaP/GaAs devices, and inverted metamorphic multi-junction (IMM) cells represent the highest-efficiency flight hardware. These samples require spectrally resolved measurement techniques because each subcell responds to a different portion of the AM0 spectrum and the overall current is limited by the weakest junction.
Coverglass-Integrated Cells and Small Assemblies
Samples may be supplied as bare cells, coverglass-interconnected cells (CIC), coupon-level laminates, or small strings and panels. Standard formats typically include 2 cm × 4 cm, 4 cm × 8 cm, and 8 cm × 8 cm geometries, although custom formats from wafer-level coupons to panel segments can be accommodated with appropriate simulator aperture and uniformity verification.
Testing Items
AM0 solar cell testing quantifies the complete electrical and spectral behavior of the device under extraterrestrial illumination. Core measurement items include:
- Light current-voltage (I-V) characteristics under standard AM0 conditions
- Short-circuit current (Isc) and short-circuit current density (Jsc)
- Open-circuit voltage (Voc)
- Maximum power point (Pmax), current at maximum power (Imp), and voltage at maximum power (Vmp)
- Fill factor (FF)
- Power conversion efficiency at 25 °C under AM0 irradiance
- External quantum efficiency (EQE) and spectral responsivity
- Temperature coefficients of Isc, Voc, and Pmax
- Series resistance and shunt resistance derived from dark and illuminated I-V analysis
- Beginning-of-life (BOL) versus end-of-life (EOL) performance comparison following radiation exposure studies
Testing Methods
Solar Simulator Configuration and Reference Standards
Testing is performed using a xenon short-arc solar simulator equipped with AM0 filtering to match the reference spectral distribution. Multi-junction devices are measured with multi-source or spectrally adjustable simulators that allow independent tuning of illumination in each subcell absorption band. Simulator quality is graded according to ISO 15387 criteria covering spectral match, spatial non-uniformity, and temporal instability, with Grade A performance typically demanded for flight qualification. Calibration is anchored to AM0 reference cells whose short-circuit current is traceable to primary standards maintained by national metrology institutes or established space-qualified calibration methods.
Current-Voltage Measurement Procedure
The sample is mounted on a temperature-controlled chuck or vacuum plate held at 25 °C ± 1 °C, and electrical contact is made using a four-wire (Kelvin) configuration to eliminate lead resistance errors. The simulator irradiance is adjusted until the appropriate reference cell, or the matched isotype component cell for multi-junction devices, reproduces its calibrated AM0 short-circuit current. A swept or pulsed voltage bias then records the complete I-V curve, from which all performance parameters and efficiency are computed. Spectral mismatch corrections based on IEC 60904-7 methodology are applied where necessary.
Spectral Response Measurement
External quantum efficiency is measured with a monochromatic probe beam, following the general principles of IEC 60904-8. For multi-junction cells, spectrally selective bias light is applied to saturate the surrounding subcells so that each junction can be characterized in isolation. The resulting EQE data, integrated with the AM0 reference spectrum, verify the photocurrent of every subcell and confirm the spectral calibration of the simulator, forming an essential cross-check within the ISO 15387 measurement framework.
Applications
AM0 solar cell testing supports the full life cycle of space photovoltaic technology, from research and development to flight acceptance. Representative applications include:
- Performance verification of solar cells for satellite and spacecraft electrical power subsystems
- Qualification and lot acceptance testing of flight-grade cells prior to panel integration
- Power budget analysis for CubeSats, small satellites, and large geostationary platforms
- Research and development of next-generation high-efficiency multi-junction architectures
- Radiation hardness studies comparing beginning-of-life and end-of-life performance
- Low-intensity, low-temperature (LILT) performance evaluation for deep-space and planetary missions
- Independent verification of record efficiencies reported by manufacturers and research groups
FAQ
What is the difference between AM0 and AM1.5 testing?
AM1.5 testing reproduces terrestrial sunlight after passage through the atmosphere at a defined path length, using an irradiance of 1000 W/m². AM0 testing reproduces the unattenuated extraterrestrial spectrum at approximately 1366 W/m², with higher ultraviolet content and no atmospheric absorption bands, which makes it the mandatory condition for evaluating space solar cells.
Why must space solar cells be tested under AM0 conditions?
Cell current generation is strongly spectrum-dependent, and the spectral differences between AM0 and terrestrial spectra cause significant deviations in short-circuit current, particularly for multi-junction devices. AM0 measurement ensures that predicted on-orbit power output accurately reflects the actual space radiation environment.
Which standards govern AM0 solar cell testing?
The primary references are ASTM E490 for the AM0 reference spectrum and solar constant, and ISO 15387 for measurement procedures, test conditions, and simulator classification. Supporting procedures from the IEC 60904 series are commonly applied for I-V measurement, spectral response, and mismatch correction methodology.
How are multi-junction cells measured under the AM0 spectrum?
Multi-junction cells are measured with spectrally adjustable or multi-source simulators, calibrated using isotype component reference cells matched to each subcell. The illumination in each spectral band is tuned so that every junction generates its calibrated AM0 photocurrent, ensuring that the current-limiting junction is correctly identified and the total current is accurate.
What are the standard test conditions for AM0 measurements?
The standard conditions specified by ISO 15387 are a cell temperature of 25 °C ± 1 °C, normal incidence irradiance at the AM0 solar constant of 1367 W/m², and a spectral distribution conforming to the reference tables over approximately 200 nm to 2600 nm.
Can AM0 testing also evaluate low-intensity and low-temperature performance?
Yes. Many laboratories offering AM0 measurement also provide low-intensity, low-temperature (LILT) characterization at reduced irradiance levels and cryogenic temperatures, which is critical for missions to the outer planets where sunlight intensity is a small fraction of the solar constant.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing