PEEK die swell ratio testing measures the elastic expansion of polyetheretherketone melt as it exits a capillary die, a critical parameter for extrusion die design, dimensional control, and rheological characterization of this high-performance engineering thermoplastic. This article explains the underlying principles, applicable international standards, sample types, test procedures, and data interpretation for PEEK die swell measurement performed by accredited third-party laboratories. Understanding die swell behavior enables processors to optimize tooling, predict part dimensions, and maintain batch-to-batch consistency of PEEK materials.
Technical Overview
Die swell, also known as extrudate swell or the Barus effect, is the phenomenon in which an extruded polymer strand emerges with a diameter larger than that of the die orifice through which it passed. For PEEK (polyetheretherketone), a semi-crystalline high-performance thermoplastic with a glass transition temperature of approximately 143 °C and a melting point of approximately 343 °C, die swell is a direct manifestation of the elastic memory of the polymer melt. Molecular chains that were stretched and oriented under high shear inside the die relax and recoil once the constraining die wall is removed, causing the extrudate to expand primarily in the directions perpendicular to the flow.
The die swell ratio (B) is most commonly defined as the ratio of the fully relaxed extrudate diameter (D) to the die orifice diameter (D0):
B = D / D0
An equivalent area-based definition uses the cross-sectional areas (A / A0), which equals the square of the diameter ratio for circular strands. Reported die swell ratios for unfilled PEEK typically range from approximately 1.1 to 1.6, depending on shear rate, melt temperature, and molecular characteristics, while fiber-reinforced grades generally exhibit lower values due to suppressed chain relaxation.
Die swell data are essential for extrusion die design, wire-coating tooling, profile and tubing dimensional prediction, and as input parameters for viscoelastic flow simulation. Standardized measurement is performed on capillary rheometers in accordance with ISO 11443 and ASTM D3835, while simplified screening can be conducted with extrusion plastometers per ISO 1133 and ASTM D1238. The Chinese national standard GB/T 25278, covering the determination of fluidity using capillary rheometers, is also widely referenced for this type of measurement.
Testing Samples
A wide variety of PEEK material forms can be evaluated for die swell behavior. Representative sample categories include:
Unfilled PEEK Resin
Natural, unfilled PEEK granules or powders serve as the baseline for die swell characterization. Because unfilled grades contain no rigid reinforcements, they display the strongest elastic response and the highest swell ratios, typically measured at melt temperatures between 370 °C and 400 °C.
Glass Fiber Reinforced PEEK
Grades containing 10 to 30 percent chopped glass fiber show markedly reduced die swell. The rigid fibers restrict molecular recoil and introduce their own orientation effects. Testing these compounds requires careful die selection to avoid fiber breakage and clogging, and swell values commonly fall between 1.0 and 1.25.
Carbon Fiber Reinforced PEEK
Carbon fiber reinforced grades, typically containing 20 to 40 percent fiber, combine low die swell with high melt stiffness. Because carbon fibers affect the viscoelastic balance of the melt, dedicated swell characterization is recommended before tooling for structural profiles or aerospace components is finalized.
Bearing-Grade and Lubricated PEEK Compounds
Compounds filled with PTFE, graphite, and molybdenum disulfide exhibit modified melt elasticity, and die swell testing of these grades supports the design of bushings, seals, and wear components produced by extrusion or compression molding.
PEEK Blends, Custom Compounds, and Regrind
Blends with other high-temperature polymers, custom-pigmented compounds, and recycled or reprocessed material can be tested to verify that process history and thermal exposure have not degraded the viscoelastic signature of the resin.
Testing Items
Typical parameters reported in a PEEK die swell test program include:
- Die swell ratio on a diameter basis at specified shear rates
- Die swell ratio on an area basis and percentage swell
- Extrudate diameter as a function of apparent shear rate, for example 100 to 10,000 1/s
- Temperature dependence of swell at 370, 385, and 400 °C
- Apparent shear viscosity measured simultaneously on the capillary rheometer
- Extrudate surface quality rating, including smooth, sharkskin, and melt fracture onset
- Influence of die geometry, particularly length-to-diameter ratio, on swell
- Comparison of virgin resin versus reprocessed or regrind material
Testing Methods
Sample Conditioning and Preparation
PEEK is mildly hygroscopic, and residual moisture causes bubbles and unstable extrudate dimensions. Samples are therefore dried, typically at 150 °C for 3 hours or 160 °C for 2 hours, and stored in a desiccator before testing. The conditioned granules are loaded into the preheated barrel of the test instrument, compacted, and allowed a 5 to 10 minute equilibration period at the set melt temperature.
Capillary Rheometer Method
The reference procedure uses a constant-speed capillary rheometer in accordance with ISO 11443 or ASTM D3835. A piston drives the PEEK melt through a capillary die, commonly 1 mm in diameter with length-to-diameter ratios of 10:1, 20:1, or 40:1. Long dies are preferred for die swell measurement because they allow the entrance flow stresses to relax, isolating the recoverable elasticity generated in the die land. The piston speed is stepped through a programmed sequence to sweep apparent shear rates from roughly 100 to 10,000 1/s, replicating the conditions found in real extrusion and injection molding processes. Applied corrections include the Rabinowitsch correction for non-Newtonian shear rate and the Bagley correction for entrance pressure loss when viscosity data are reported alongside swell.
Extrudate Diameter Measurement
Diameter can be captured either off-line or in-line. In the off-line approach, extrudate strands are allowed to relax and cool in air or on a non-stick surface, and their diameters are measured with a calibrated optical microscope or micrometer at several axial positions, with the results averaged. In-line measurement uses a non-contact laser diameter gauge or optical scanner positioned 5 to 20 mm below the die exit, which records the diameter of the still-molten strand in real time. Both approaches must specify the measurement location, because the extrudate continues to swell over a distance of several die diameters before reaching its asymptotic, fully relaxed diameter. Shrinkage upon cooling and crystallization is reported or corrected separately when solid-state dimensions are of interest.
Extrusion Plastometer Screening Method
For rapid quality-control screening, a melt flow indexer operated per ISO 1133 or ASTM D1238 can be fitted with a die swell attachment or laser micrometer. Although the single low shear rate of the standard test limits extrapolation to production conditions, the method is useful for batch comparison of incoming PEEK resin.
Data Reduction and Reporting
The die swell ratio is computed as B = D / D0, where D is the mean extrudate diameter and D0 is the die diameter, and the area ratio equals B squared. The test report documents the material grade, drying history, barrel and die temperatures, die geometry, shear rate sequence, measurement technique and location, individual swell ratios at each shear rate, and any observed surface defects such as sharkskin or melt fracture. Many laboratories also plot swell versus shear rate, which typically increases with shear rate before leveling off or decreasing at very high rates.
Applications
Die swell ratio data for PEEK support a wide range of engineering and quality functions:
- Extrusion die and sizing sleeve design for rods, sheets, tubes, and custom profiles
- Wire and cable insulation tooling, where swell compensation determines coating thickness
- Medical extrusion of catheter liners, monofilament, and thin-wall tubing requiring tight tolerances
- Input data for viscoelastic simulation models used in die and mold flow analysis
- Injection molding gate, runner, and flow balancing calculations
- Incoming resin inspection and batch-to-batch consistency verification
- Material qualification support for aerospace, automotive, semiconductor, and oil and gas specifications
- Research into structure-processing relationships, including the effect of molecular weight distribution on melt elasticity
FAQ
What is a typical die swell ratio for PEEK?
Unfilled PEEK commonly shows diameter-based swell ratios of approximately 1.1 to 1.6 at processing shear rates, with the exact value depending strongly on shear rate, melt temperature, and molecular weight. Glass and carbon fiber reinforced grades usually fall between 1.0 and 1.25 because the fibers suppress elastic recovery.
Why does PEEK exhibit die swell?
PEEK molecular chains are stretched and oriented by the strong extensional and shear deformation in the die entrance and die land. When the melt exits and the wall constraint disappears, stored elastic energy is released, the chains recoil, and the extrudate expands perpendicular to the flow direction. This is a classic viscoelastic response governed by the first normal stress difference of the melt.
Which standards govern the test?
Capillary rheometer measurements follow ISO 11443 and ASTM D3835; screening with an extrusion plastometer follows ISO 1133 and ASTM D1238; and GB/T 25278 is the corresponding Chinese national method for capillary rheometry. Testing should be performed by accredited third-party laboratories or qualified in-house rheology facilities using calibrated equipment.
How can die swell in PEEK processing be reduced?
Practical measures include raising melt temperature within the allowed processing window of roughly 370 to 400 °C, increasing die land length, lowering output rate or shear rate, selecting a lower molecular weight or fiber-reinforced grade, and applying slight draw-down tension immediately after the die exit.
How much sample is required for a test?
A full multi-shear-rate characterization generally consumes approximately 50 to 150 grams of PEEK granules or pellets, depending on barrel size and the number of test temperatures. Samples should be supplied with grade identification and, ideally, the resin lot data sheet for traceability.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing